IPMP CONFIGURATION IN SOLARIS 10 PDF

IPMP CONFIGURATION IN SOLARIS 10 PDF

These topics include IPv4 and IPv6 network configuration, managing TCP/IP 1. Oracle Solaris TCP/IP Protocol Suite (Overview) The default is 10 seconds. Oracle Solaris Administration: IP Services Oracle Solaris 10 1/13 Information An IPMP configuration typically consists of two or more physical interfaces on the . For IPMP configuration tasks, refer to Chapter 31, Administering IPMP (Tasks). Oracle Solaris IPMP involves the following software: You can configure one of the interfaces down to 10 megabits and still place the two interfaces into the.

Author: Yozshurisar Kall
Country: Togo
Language: English (Spanish)
Genre: Politics
Published (Last): 20 October 2017
Pages: 13
PDF File Size: 11.19 Mb
ePub File Size: 16.83 Mb
ISBN: 854-3-87366-738-4
Downloads: 40963
Price: Free* [*Free Regsitration Required]
Uploader: Dashicage

You do not need to mark an IPv6 test address as deprecated to prevent applications solaeis using the test address. IPv4 does not use a deprecated address as a source address for any communication, unless an application explicitly binds to the address.

You can observe this flag in the status lines for the interface in the ifconfig output.

How to configure Solaris 10 Probe based IPMP

Target Systems Probe-based failure detection uses target systems to determine the condition of an interface. Self Paced Courses Live Webex. IPMP detects the following types of communication failures: After detecting a failure, IPMP begins failover. Detaching NICs All requests to detach system components that contain NICs are first checked to ensure that connectivity can be preserved.

If one of the group names contains a space, these group names look the same in the status display. Fist i am going to disable eg1 and let see what happens.

  LINEAR ALKYL BENZENE MSDS PDF

If you want the configuration to be invoked in the current session, do steps 1, 2, and, optionally 3.

Configurationn to these restrictions, you must use the ifconfig command to mark any test addresses as deprecated and -failover prior to setting the interface as standby. For instructions, refer to Configuring Target Systems.

When a failure occurs, the data addresses on the failed interface migrate to the standby interface. Failure Detection and Confjguration Failure detection is the process of detecting when an interface or the path from an interface to an Internet layer device no longer works.

By default, only link-based failure detection detects physical link failures is enabled but probe-based failure detection detects failures on IP layer is disabled:. Dynamic reconfiguration DR is conifguration ability to reconfigure a system while the system is running, with little or no impact on existing operations. Administering Network Interfaces Tasks 7.

How to configure Solaris 10 Link Based IPMP – The Geek Diary

This chapter contains the following information: Each interface can be configured with an IP test address. Probe-based failure detection is performed per VLAN-link. For more information on probe-based failure detection, refer to Probe-Based Failure Detection.

A single interface can be configured in its own IPMP group.

How to configure Solaris 10 Link Based IPMP

Place each physical interface into an IPMP group. Repair detection is the process of detecting when a NIC or the path from a Configurahion to an Internet layer device starts operating correctly after a failure.

  3212 SAYL KANUN PDF

You can check the status of an interface by issuing the ifconfig interface command. Awesome article and nicely explained. When the failover of address As a result of load spreading, higher throughput is achieved. RCM records the configuration information associated with any NIC’s that are detached from a running system. The only valid IPv6 test address is the link-local address of a physical interface. Its really awesome article.

IP Security Architecture Overview This flag indicates that the interface is currently not to configurarion used for data traffic. Troubleshooting Network Problems Tasks Probe-Based Failure Detection The in.

Therefore, the no value is only useful for reporting failures and does solarjs directly improve network availability. For example, you can use the ifconfig command to obtain the status of a standby interface. IP Security Architecture Overview The minimum repair detection time is twice the failure detection time, 20 seconds by default, because replies to 10 consecutive probes must be received.

The dummy address is removed when a subsequent failback takes place. Leave a Reply Cancel reply.

Test addresses are configured as logical interfaces of the physical interface that you specify to the ifconfig command.