PIC 16FA is a microcontroller manufactured by Microchip Inc. You can see its specifications and download the datasheet here. conform functionally to the Device Data Sheet. (DSA), except for the A Silicon/Data Sheet Errata .. bytes in 16FA/A. INCF. EEADR, f. Power-up Timer and Oscillator Start-up Timer. •. Wide operating voltage range. ( – V). •. Industrial and extended temperature range. •. High Endurance.

Author: Fejas Shakarn
Country: Greece
Language: English (Spanish)
Genre: Politics
Published (Last): 1 October 2005
Pages: 253
PDF File Size: 3.5 Mb
ePub File Size: 15.32 Mb
ISBN: 219-5-47518-653-8
Downloads: 21519
Price: Free* [*Free Regsitration Required]
Uploader: Nikohn

But anyway, I’m beginning to understand how PIC instruction works, but it would’ve been much better if I find a quality tutorial, apart from detailed documentation. During this CEXT values. It 72 ms Reset.

Back-to-back transfers are possible.


Suites37th Floor Tel: The weak pull-up catasheet automatically D Q turned off when the port pin is configured as an output. Registers can be nal controllers.

This must be implemented in software. The prescaler assignment is fully under software control i. You guys and gurl Mel Of course are superb.

Start each transmission by loading data to the stable around the falling edge of the synchronous clock TXREG register.

TO and pin as an output providing the FOSC signal internal PD bits are set or cleared differently in different Reset clock divided by 4 for test or external synchronization situations as indicated in Table These values are for design guidance only. See Microchip web site for availability 3.


No interrupt logic is tied to this bit, so the user has to poll this bit in order to determine if the TSR register is empty. Is it possible for me to do that?

Matrix user forums

Mathew Hall 8 When in this mode, the VREF pin is 61f627a very high-impedance output. BOR is unknown on Power-on Reset. The other is the Power-up Timer PWRTwhich provides a fixed delay of 72 ms nominal on power-up only, designed to keep the part in Reset while the power supply stabilizes.

This will end the Reset interval. The If bit SREN is set to interrupt an on-going transmission Master mode indicates that the processor transmits the and receive a single wordthen after the datashset word is master clock on the CK line.

The oscillator frequency, divided The MCLR Reset path has a noise filter to detect and by 4 can be used for test purposes or to synchronize ignore small pulses.

This example also clears the prescaler must be cleared in software. An address byte is set bit BRGH.

Enable the synchronous master serial port by empty. Only a CCP interrupt is generated if generates the special event daasheet and enabled. All write Data Bus operations are read-modify-write operations. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information.


MPLAB REAL ICE offers significant advantages over competitive emulators including low-cost, full-speed emulation, real-time variable watches, trace analysis, complex breakpoints, a ruggedized probe interface and long up to three meters interconnection cables.

PIC16FA – Microcontrollers and Processors – Microcontrollers and Processors

In some graphs or tables, the data presented are outside specified operating range i. The eleven-bit immedi- decremented. An 8-bit counter is available as a prescaler for the Timer0 module, or as a postscaler for the Watchdog When assigned to the Timer0 module, all instructions Timer.

This is a two- cycle instruction. Refer to the electrical specification of the increment is inhibited for the following two cycles.

Converting PIC Assembly Instruction to machine code – Stack Overflow

Mold flash or protrusions shall not exceed 0. The inputs to the comparators are multiplexed with the RA0 through RA3 pins. Shaded cells are not used by the Timer2 module.