Download Heatline C28 manual. You have chosen to download this manual. Heatline C28, please click on the PDF link below. The boiler’s ‘Log Book’ must be completed at each Service visit. By means of a manual switch the C24/C28 can be set to operate in one of two operating modes, . Boiler Manuals for the Heatline Compact C28 appliance.

Author: Zolot Faejas
Country: United Arab Emirates
Language: English (Spanish)
Genre: Love
Published (Last): 7 July 2005
Pages: 134
PDF File Size: 11.2 Mb
ePub File Size: 17.27 Mb
ISBN: 815-9-80171-691-2
Downloads: 66772
Price: Free* [*Free Regsitration Required]
Uploader: Kehn

Agile11 Oct As always running heating every week for five mins keeps things moving! Whilst every attempt is made to ensure the accuracy of information contained on this help centre, errors can occasionally occur.

When the boiler is intended for use with LPG it must not be installed in a room or internal space below ground level! Save energy Energy saving tips. I would consider a boiler change although most of us are a bit cash straped at the moment it may be money beter spent. Unclip the sensor from the pipe 5.

Ideal Mini C28

hewtline Carry on browsing if you’re happy with this, or click here to manage cookies. You must log in or sign up to reply here. Landlords Landlords cover Landlords repair Landlords insurance.

Saunier Duval Boiler Parts. We will source it from our suppliers and aim to get it to you within 3 – 5 working days. Verify the igniter unit connections. The CH was switched on prior to this.

The air pressure switch is located on the top of the expansion vessel 4. Underfloor heating contact fault. That can be achieved by fitting dip switch number 5 into the position ON.


Remove the electrical connections to the PCB by pulling carefully, noting the locations of all the terminals mwnual shown on the picture below 5. Were we able to answer your question s? By continuing to use this site, you are agreeing to our use of cookies.

heatline c28 Questions & Answers (with Pictures) – Fixya

The sensor i ordered arrived next day changed this but has never fired up? Re-connect sensing tube and all the electrical leads 7. Put those aside till the re-assmble part as shown on the picture below.

Remove the clop on the pump body and then release the pipe of the expansion vessel as shown on the picture below. If you want to access the the potentiometers you should simply remove the cover panel and you will see those at the rear as shown on the picture below. Heatline boiler problem Pinkeric21 Junin forum: Re-assemble the boiler in reverse order Secondary Heat Exchanger replacement 1.

Ask Vaillant | Domestic Boilers | Vaillant

The first thing that i noticed was that the CH heating was on even though it was in summer mode. If seals are damaged- replace as healtine 8. Your appliance is equipped with a number of safety devices that will lock out your boiler functionality in instances where fault would heatlone permanent appliance damage or cause health safety issue.

Permanent temperature difference between flow and return heating sensors. Verify the return gas circuit gas valve open.

The Vaillant Group cannot accept any responsibility for any reliance upon such information, any omissions or any subsequent loss or damage. Refit in reverse order to removal, the polarity of the wires to the modulating coil is not important, replace any damaged heatlie as required X This part also fits Users found this page by searching for: Pump will run for a additional secs in order to release the heat from the boiler itself.


Before putting the appliance into operation remember to drain the plastic discharge pipe. Verify the flow and return heating sensor connections. Remove the pressure sensor by turning it in an anticlockwise direction 5.

Locate the central heating sensor — it is on left side of the combustion chamber on the outlet of the primary heat exchanger as shown on the picture below. Fluctuation of flame signal.

Remove the two screws which connect the heat exchanger to hydraulic circuit 5. The Heatline C24 and C28 are a range of Condensing boilers that are currently not in production. The wall on which your appliance will be mounted should be able to support the weight of the boiler for an extensive period of time. You can use the user manual for detailed instructions on how this is checked. When the demand for central heating is fulfilled, heeatline burner will shut down and the appliance will come to stand-by mode, until the next hot water or heating demand.

Pull forward the heat exchanger and remove Port valve can be found on v28 hydro-block.

As Kev says the diverter valve has failed. You can open the cupboard door or provide a mm clearance at the front.