Information you will need about your DSL-GT Wireless ADSL Router: D- Link ADSL devices incorporate the recommendations of the ADSL Forum. Modem Dlink DSLT/T/T/GT/GT – Bootloader ADAM2 . Manuale firmware Acorp (v. manuale ) -> Download. D-Link DSL B3 User , , M. [ ], D-Link DSL Manuale Router DLink DSL-GT – , , M.
|Published (Last):||18 April 2005|
|PDF File Size:||19.13 Mb|
|ePub File Size:||20.50 Mb|
|Price:||Free* [*Free Regsitration Required]|
Table of Contents Add to my manuals Add. Double-click dsp-g624t Network and Dial-up Connections icon. Dynamic IP default setting for. It is recommended that your collect and record this information here, or in some other secure place, in case you have to re-configure your ADSL connection in the future.
Introduction This section provides a brief description of the Router, its associated technologies, and a list of Router features. You may stop using the Setup Wizard at any time by clicking the Exit button. If you need to change settings from a previous sdl-g624t, click the Back button.
Filters Community Traps Filters Filter rules in the Router are put in place to allow or block specified traffic.
The rules are configured for individual devices based on MAC address. The access point can be placed on a shelf or desktop, ideally you should be able to see the LED indicators on the front if you need to view them for troubleshooting.
Upon restarting the Router will automatically establish the WAN connection. Note Use the Firmware Upgrade window to load the latest firmware for the device. Note that the device configuration settings may return to the factory default settings, so make sure you save the configuration settings with the System Settings window described above.
D-Link DSL-G624T User Manual
Select a key by clicking a radio button on the left, select an encryption level from the drop-down menu on the right, and then enter the proper-length key. If you have been given instructions to change the Modulation method used, select the desired option from the Modulation Type drop-down menu and click the Apply button.
The window will display settings that are appropriate for the connection type you select. You will need to supply the IP addres, Subnet mask and Defualt Any changes made to these settings may adversely affect your wireless network. The router offers, or bit encryption with four keys available. For applications or circumstances where packet loss or packet delay is a concern, ATM QoS can be adjusted to minimize problems. This sets the system time used for dsl-g624y Router.
DSLB Router Wireless G ADSL 2+ con 4 Porte 10/ | D-Link Italia
Up to eight PVCs to eight separate destinations can be created and operated simultaneously utilizing the same bandwidth. This defines both the connection type and encapsulation method used for your ADSL service.
To add a new virtual connection: If you wish to return to the previous window during the setup process, click the Back button. WEP encrypts the data portion of each frame transmitted from d-,ink wireless adapter using one of the predefined keys.
Page 9 Page 10 – Information you will need about your lan Use the navigation buttons to view or scroll log pages. There are two general types of protection DoS, Port Scan that can be enabled on the Router, as well as filtering for specific packet types sometimes used by hackers.
This will dsl-6g24t the chosen IP address used out of the available addresses in the dynamic IP address pool and give a permanent lease time for the IP address to the selected device. When enabled, it allows other devices that support UPnP to dynamically join a network, obtain an IP address, convey its capabilities, and learn about the presence and capabilities of other devices.
To remove any MAC address from the list, click the radio button in the left column of the list for dsl-g6244t MAC address to be removed and click the Apply button. The connection ports are typically labeled as follows: The initial window summarizes the setup process.
This should be obtained from your ISP. Only a single filter is required. Under certain mauale, changes may be benefit performance. A Ping test may be done through the local or external interface to test connectivity to known IP addresses. Click the Apply button to activate the new password. This IP address is not protected by NAT and will therefore be visible to agents on the Internet with the right type of software.
Filter rules can be set up for source, destination or both. Dsl-f624t the previous chapter for a description of the Home directory windows.
The Network dialog box displays with a list of currently installed network components. Configure a dsl-g24t of manale for forwarding. If you are satisfied that you have entered all the necessary information correctly, click the Restart button to save the new configuration settings and restart the Router. This may be done for security or to improve network efficiency. Security for wireless communication can be accomplished in a number of ways.
To modify any previously created filter rule, click on the note pad icon in the right hand column of the Filter List for the set you want to configure.
Wireless access can also be controlled by selecting MAC addresses that are allowed to associate with the device. Select the interface for which you want to view packet statistics and the information will appear below. Three Port Filter Another style of filter is installed at the same point where the Router connects to the telephone line. Your ISP has given this information to you.
Type the lowest numbered port in the range in the Port Start space. This section provides a brief description of the Router, its associated technologies, and a list of Router features.
In this case you need to change this Static IP setting to. Open, Shared, or Both.