Publication UMA-EN-P – November Table of Contents . User Manual UM to assign an IP address to the MicroLogix. controller. Publication INC-EN-P – October Important . Manual UM .. publication UM, for more information on surge suppression. rm_-en-p – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Document Number IN UM
|Published (Last):||8 January 2008|
|PDF File Size:||1.73 Mb|
|ePub File Size:||1.54 Mb|
|Price:||Free* [*Free Regsitration Required]|
Wiring category 1 2 – on signal ports 2 – on power ports 3 – on communications ports Terminal screw torque 0.
IN – Rockwell Automation
Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Secure the template to the mounting surface. Replace the battery un001 the controller is powered on.
The terminals will accept a 6. Soal meeting 9th Part of speech: Mount your DIN rail. Because of this difference, and also because of the wide variety of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable. Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
Follow these steps to connect the replaceable battery. Linea centrale della guida DIN. Make sure your controller is spaced properly see Controller Spacing on page 12 for more information.
Output 2, 3 and 4 may be 11766 like the other FET enn outputs, but in addition, within a limited current range, they may be operated at a higher speed. For an additional level of technical phone support for installation, configuration and troubleshooting, we offer TechConnect support programs.
Drilled fragments that fall into the controller could cause damage. Replacing the battery when the controller is powered down will lose all user application memory.
1766-IN001 – Rockwell Automation
MicroLogix Instruction Set Reference Manual RM A reference manual that contains data and function files, instruction set, and troubleshooting information for MicroLogix Ensure that the battery wire connector is inserted into the connector port if your application needs l power. It must be mounted within an enclosure that is suitably wn for those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts.
For Safety information on the handling of lithium batteries, including handling and disposal of leaking batteries, see Guidelines for Handling Lithium Batteries, publication AG Refer to the SLC Lithium Battery Installation Instructions, publication IN, for more information on installation, handling, usage, storage, and disposal of the battery. Wear an approved grounding wriststrap. Finger-safe cover TIP If you wire the terminal block with the finger-safe cover removed, you may not be able to put it back on the terminal block if the wires are in the way.
Additional noise immunity can be obtained by routing the cables in grounded conduit. Replace the cover as shown below. Power Loss in Transmission Lines. Make sure that the placement of the controller on the DIN rail meets the recommended spacing requirements see Controller Spacing on page 12 for more information. For more information on proper grounding guidelines, refer to the Industrial Automation Wiring and Grounding Guidelines, publication Repeat steps 1 and 2 for the second DIN rail latch.
Use a power supply that matches the transmitter specifications as shown. In no event will Rockwell Automation, Inc. DIN rail mounting dimensions are shown below. Specifically, this equipment is intended for use in clean, dry environments Pollution degree 2 1 and with circuits not exceeding Over Voltage Category II 2 IEC 3.
Scripting must be enabled to use this site.
Prolonged exposure to direct sunlight could degrade the LCD display. When combining products within a system, the most adverse temperature code lowest “T” number may be used to help determine the overall temperature code of the system.
You can also contact a special Customer Support number for initial help in getting your product up and running. Do not touch circuit components inside the equipment. Wiring Your Analog Channels Analog input circuits can monitor voltage signals and convert them to serial digital data as shown in the following illustration.